Skip to content

Changelog

Every change to Mirox, grouped by month. Filter by group or by kind of change.

Clear filters

November 20261

AgentFeatureMajorData collection

A plant controller can now be added as a data logger

A plant controller can now be added as a data logger, with the on-site agent reading the power, energy, operating state, string positions and fault codes of the plant's string inverters. Plants receive this with their next agent update.

mirox 2.15.875 – 2.15.881mirox-agents 3.2.258 – 3.2.264

October 20264

Web appFeatureData collection

Sensors and feed-in meters show their logger and data state

On the plant's components page, in its sensor and meter tabs, each irradiation sensor and feed-in meter now shows which data logger serves it, its data state and its last data time. A logger filter narrows the table.

mirox 2.15.736 – 2.15.754
AgentFeatureMajorData collection

An inverter can now be added as a data logger

An inverter can now be added as a data logger, reading its live output, energy, status and alarm codes, and backfilling its day curve from the inverter's web interface at 15-minute steps. Plants receive this with their next agent update.

mirox 2.15.646 – 2.15.652mirox-agents 3.2.160 – 3.2.161
AgentFeatureMajorData collection

A wind plant's SCADA can now be added as a data logger

A wind plant's SCADA can now be added as a data logger, reading each turbine's production, its stop commands with their cause, the grid operator or the direct marketer, and the grid operator's setpoint. Plants receive this with their next agent update.

mirox 2.15.614 – 2.15.619mirox-agents 3.2.144
AgentFeatureMajorData collection

A power quality analyzer can now be added as a feed-in meter

A power quality analyzer can now be added as a feed-in meter and reads the grid, the PV feeder or the battery feeder. Plants receive this with their next agent update.

mirox 2.15.587 – 2.15.592mirox-agents 3.2.131

September 20268

AgentFeatureMajorData collection

A plant controller can now be added as a data logger

A plant controller can now be added as a data logger, reading the grid operator's active-power setpoint as a percentage of installed capacity or the plant's irradiance sensor. Plants receive this with their next agent update.

mirox-agents 3.2.120 – 3.2.123mirox 2.15.570 – 2.15.571
AgentFeatureMajorData collection

A Meier-NT ADL-MX data logger can now be added

A Meier-NT ADL-MXmini or ADL-MXSpro data logger can now be added and reads the Power-One / ABB Aurora inverters and Si irradiance sensor behind it: power, voltages, currents, temperatures, irradiation, wind speed, daily and total energy, and each inverter's reported operating state. Plants receive this with their next agent update.

mirox 2.15.497 – 2.15.503mirox-agents 3.2.87 – 3.2.91
Read more in the documentationData loggersInverter status codes
AgentFeatureMajorData collection

Bachmann SPPC and mtu EnergyPack now serve as data loggers

A Bachmann SPPC park controller and an mtu EnergyPack battery can now be added as data loggers, the SPPC reading the grid connection point and the grid operator's and direct marketer's limits, the EnergyPack its state of charge, health, stored energy and power limits, with the next agent update.

mirox 2.15.486 – 2.15.493mirox-agents 3.2.76 – 3.2.82
Read more in the documentationData loggers
AgentFeatureData collection

Each Janitza meter can now be assigned what it reads

At a plant with a battery behind its grid connection point, each Janitza meter can now be assigned what it reads: the grid connection point, the PV feeder or the battery feeder. PV and battery readings then stay separate from the plant's grid figures, with the next agent update.

mirox 2.15.486 – 2.15.493mirox-agents 3.2.76 – 3.2.82
Read more in the documentationData loggers
AgentFeatureMajorData collection

Vestas wind turbines are now read through VestasOnline

A Vestas VestasOnline SCADA server can now be added as a data logger, and every turbine behind it is read — power, wind and its lifetime energy counter — and listed on the wind plant's "Turbines" page. Plants receive this with their next agent update.

mirox 2.15.428 – 2.15.442mirox-agents 3.2.32 – 3.2.41
Read more in the documentationData loggers
Web appFeatureMajorData collection

A plant's history now imports from its previous monitoring system

The "Import" tab on a plant's "Dataflow" page now takes the ZIP archive from the plant's previous monitoring system and matches its devices to components by serial number or name. The import runs day by day and can be paused, stopped, or have what it wrote deleted.

mirox 2.15.420 – 2.15.564
Web appFeatureMajorData collection

The wizard now adds SMA Data Manager and Sungrow loggers

Devices behind an "SMA Data Manager / Power Manager" or "Sungrow Logger" data logger are now listed and their alarms reach the plant's event list. A blue'Log logger gains a "String monitoring" section.

mirox 2.15.397 – 2.15.406
Read more in the documentationData loggers

August 20268

July 20262

June 20262

May 20264

April 20262

January 20265