Skip to content

June 2026

Changes released in June 2026.

Open in the full timeline

AgentFixMajorProduction & yield

Expected production no longer exceeds the grid transmission limit

Expected production, and the maximum under a clear sky, no longer rise above a plant's "Grid Transmission Limit". A grid operator's percentage setpoint now counts against that limit, not the inverters' combined peak. Plants receive this with their next agent update.

mirox-agents 3.1.112
AgentFixMajorSolar equipment

Strings now keep a confirmed orientation after two clear days

On plants where clear days are often curtailed, most strings used to end with only a partial result. Two clear days that agree are now enough for a confirmed orientation, instead of three. Plants receive this with their next agent update.

mirox-agents 3.1.112
AgentFixMajorSolar equipment

Strings get a result on days the inverters ran under a limit

Strings now get a result on days when the inverters ran under a power limit. Before, any limit below 100 percent made the check discard the whole day, so those days gave no result. Plants receive this with their next agent update.

mirox-agents 3.1.108 – 3.1.110
Web appImprovements and fixesSolar equipment

An analysis now fills in while it runs, instead of only once each of its days is finished.

  • While an analysis runs, the day being processed shows how many strings already have a result, not only once that day is finished.
  • The analysis summary now lists strings whose orientation could only partly be confirmed as a group of their own, apart from fitted and unassessable strings.
  • Pages and downloads from a device opened through remote access no longer stop part-way once the remote-access configuration is downloaded again.
  • Grey stretches now appear between a data logger's readings only where the logger really stopped reporting.
mirox 2.14.144 – 2.14.147
Read more in the documentationComponentsVPNData loggers
AgentImprovements and fixesSolar equipment

The on-site analysis now keeps the result of every string, even on a large plant.

  • After an on-site analysis on a large plant, every string keeps its result, where a few hundred of them previously went missing.
  • Changes to a plant's components take effect in the on-site analysis started right after, instead of up to an hour later.
  • Becker PV-Control data loggers can now be read by mapping the values they send.
mirox 2.14.144 – 2.14.147mirox-agents 3.1.108 – 3.1.110
Read more in the documentationComponentsData loggers
Web appImprovements and fixesProduction & yield

Two more values can now be recorded in a plant's settings.

  • A plant's "Grid Transmission Limit" can now be entered in its settings, and its "Yearly Degradation" in percent beside the monthly PR targets.
  • A data logger now opens on a "Mapped metrics" overview, where one click removes a mapped reading and the change is saved straight away.
mirox 2.14.142 – 2.14.143
Read more in the documentationData loggers
Web appFixMajorProduction & yield

Production now covers days the feed-in meter did not report

Days when the feed-in meter did not report, or reported an implausible value, no longer drop out of production figures. Production for those days is taken from the inverters instead.

mirox 2.14.137 – 2.14.141
Web appFixCurtailment & grid limits

Curtailment by settlement method is compared alike in the revenue API

The comparison of curtailment energy by settlement method in the API's revenue response previously depended on the data-quality filter and the plant's clipping setting. It now counts each method's booked curtailment energy alike, with inverter clipping considered.

mirox 2.14.137 – 2.14.141
Web appImprovements and fixesNetwork & remote access

The status dots of data loggers and network devices now follow the live readings. A device that went down no longer shows green.

  • When a device's web page cannot be opened through remote access, a Mirox page names the reason instead of a raw error.
  • Each of a device's web pages can be given its own login, separate from the device login.
  • Devices that block unfamiliar addresses, such as a FRITZ!Box with rebind protection, can now be opened as well.
  • On a plant's "Market" tab, "Accounting country" can now be set to "None" for a plant without EEG accounting, which hides the EEG values.
  • A QReader data logger's value mapping now offers "By External (W)", a power limit set by external control in watts, optionally tied to a segment.
mirox 2.14.137 – 2.14.141
Read more in the documentationProxyData loggers
AgentFixMajorCurtailment & grid limits

Marketer curtailment no longer counts during negative spot prices

In Germany, curtailment by the direct marketer no longer counts during hours with a negative day-ahead price. Curtailment energy and the compensation calculated from it for those hours decrease. Plants receive this with their next agent update.

mirox-agents 3.1.97 – 3.1.98
AgentFixProduction & yield

Feed-in power now counts every meter behind one QReader data logger

Where all grid meters are read through one QReader data logger, feed-in power behind curtailment losses and the performance ratio now sums every reporting meter instead of keeping only one. Curtailment losses decrease and the performance ratio rises, while figures already issued keep their value until a period is rebuilt. Plants receive this with their next agent update.

mirox-agents 3.1.97 – 3.1.98
Web appImprovements and fixesData collection

A data logger's value mapping can now be corrected after setup through "Edit metrics". Strings on several selected inverters can now be edited in one step on a plant's components page.

  • Newly detected components show "Collecting data…" for their first two hours.
  • A plant's pages no longer show the on-site agent as not responding right after a configuration change restarts it.
  • A plant's solar analysis page no longer shows a clear-day count larger than the days its inverters have been reporting.
  • The mapping of an irradiation sensor on a data logger now records whether it measures horizontal or module-level.
mirox 2.14.133 – 2.14.136
Read more in the documentationData loggersComponents
Web appImprovements and fixesThe app itself

A plant's production charts now fill the hours a remote-access outage left without data with expected production. The "Forecast" page now lists the hours of today and tomorrow with a negative day-ahead price.

  • A plant's ticket list can now be filtered, sorted and paged.
  • A plant's networking page shows each device's type, address and online status.
  • A contact's SEPA direct-debit mandate can now be signed from the contact's actions.
  • A plant's component table now marks offline devices.
  • A plant's day power chart now marks snow periods.
mirox 2.14.124 – 2.14.131
AgentFixMajorCurtailment & grid limits

Flat-rate curtailment no longer counts the night hours

Curtailment energy under the flat-rate (pauschal) settlement method was too high because the night hours counted as well. It now covers only the energy lost while the sun was up, so those figures and the compensation based on them go down. Plants receive this with their next agent update.

mirox-agents 3.1.73
Web appImprovements and fixesThe app itself

A combiner box's figures open again. Deleting a plant's remote access now asks for its name to be typed first.

  • Deleting a remote-access server or a connected site now asks for its name, and the warning states that its keys are gone for good.
  • A combiner box's figures open again instead of failing with an error.
  • A connected site that has been deleted no longer counts in the plant's remote-access status.
  • When plant documents are uploaded, the suggested installed capacity now covers every construction phase, and the grid operator and planning company are recognised more reliably.
  • A subnet typed but not added to the list now triggers a warning instead of the connected site being saved without it.
  • Times from late yesterday no longer show as today, and dates written in words now follow the calendar day.
mirox 2.14.75 – 2.14.76
Read more in the documentationVPNRemote accessComponents
Web appFixMajorCurtailment & grid limits

Saving a market option no longer switches off inverter clipping

Saving any option in a plant's market settings no longer sets inverter clipping to be ignored. Since 1 June, plants where that happened showed too much curtailment energy and a compensation calculated from it that was too high as well.

mirox 2.14.71 – 2.14.74
AgentFixProduction & yield

Forecasts now follow each string's actual orientation and tilt

Expected production and the five-day forecast now follow the direction and tilt each string actually has. Before, every string was assumed to face south at 15°, so plants built any other way saw figures that were off. Plants receive this with their next agent update.

mirox 2.14.71 – 2.14.74
Read more in the documentationComponents
Web appFixMajorCurtailment & grid limits

Curtailment now counts the production the imposed limit forbids

Curtailment on the dashboard and on a plant's production page is now the production the imposed limit forbids, attributed to the grid operator or the direct marketer and shown per settlement method. Figures from 1 June are calculated this way, while earlier periods keep the figures of the previous calculation and are marked "Legacy Data".

mirox 2.14.68 – 2.14.70
Web appImprovements and fixesProduction & yield

A plant's production page is rebuilt around the performance ratio. Remote access now reaches several connected sites at once.

  • Several connected sites can now be reached through one plant's remote access, with each site's subnets, keys and status managed on the "Peers" tab.
  • The production page is rebuilt: performance ratio per source, an inverter table, site specifications, and a day curve with the clear-sky ceiling and expected production.
  • Stretches where the plant could not be reached are now filled with the energy the weather model expects, shown as "Expected (no connection)".
  • The API now returns a plant's revenue and EEG compensation per month or year through GET /v1/park/{uid}/revenue, with Marktwert, Marktprämie and curtailment per settlement method.
  • The dashboard button again opens on the whole selected day, instead of on an empty range.
  • A plant's address is saved again when it is changed in the plant's details.
mirox 2.14.68 – 2.14.70
Read more in the documentationVPNRemote access
AgentImprovements and fixesProduction & yield

Orientation and tilt are now detected on plants that only measure at the inverter. Expected energy no longer jumps between the days of the five-day forecast.

  • Orientation and tilt are now detected on plants that only measure at the inverter, from the inverter's power for its strings.
  • Expected energy no longer jumps between forecast days, as the five-day forecast keeps one performance ratio across all of them.
mirox-agents 3.1.67
Read more in the documentationComponents
AgentFixMajorProduction & yield

Performance ratio steadies on plants with several feed-in meters

The performance ratio of a plant that measures feed-in energy with more than one meter no longer jumps between implausible values. It now adds up all those meters, including on plants that report combined inverter power as the feed-in measurement. Plants receive this with their next agent update.

mirox-agents 3.1.61 – 3.1.65
Web appImprovements and fixesNetwork & remote access

Strings added by hand can now be deleted, and a network scan that finds nothing says why.

  • Strings added by hand can be selected on the components page and deleted after a confirmation prompt, while detected strings stay.
  • A network scan that finds nothing now says whether it could not reach the plant network or the scanned range held no devices.
  • All address ranges of a direct remote-access connection are edited in one list and saved together; ranges already used on the plant are flagged.
  • A plant's on-site agent keeps running when the plant is removed from an organization's remote access or that remote access is deleted.
mirox 2.14.57 – 2.14.67
Read more in the documentationComponentsVPNRemote access
AgentImprovements and fixesData collection

A Huawei data logger that could not be reached at first now finds its inverters on its own. A device that refuses extra connection details opens its web interface.

  • A Huawei data logger that cannot be reached when the on-site agent starts shows its inverters within five minutes, without a restart.
  • The web interface of a device that refuses extra connection details can now be opened.
mirox-agents 3.1.61 – 3.1.65
Read more in the documentationData loggersProxy
Web appImprovements and fixesNetwork & remote access

The day power chart now marks only connection losses that really happened and names the remote access connection that dropped. The record of remote access activity opens on the most recent weeks.

  • On a plant without remote access, the day power chart no longer marks the whole day as a lost connection.
  • Where a connection really dropped, the chart now names the remote access connections affected, or states that their state is unknown.
  • The record of remote access activity opens on the most recent weeks, and the weekday labels stay in place while scrolling.
mirox 2.14.55
Web appImprovements and fixesSolar equipment

Strings can now be added to many inverters or combiner boxes in one step instead of one device at a time.

  • Strings can be added to several inverters or combiner boxes in one step, with all of a plant's inverters selected at once.
  • Editing a single string now opens with that string's current values already filled in.
  • If the connection to a data logger drops during its setup, "Reconnect" resumes it and keeps the step, credentials and value mapping.
  • On plants without combiner boxes, adding a string no longer asks where to attach it.
mirox 2.14.49 – 2.14.54
Read more in the documentationComponentsData loggers
AgentFixMajorProduction & yield

Curtailment and performance ratio now sum every grid meter

At a plant with more than one grid meter, the feed-in power behind curtailment losses and the performance ratio was previously neither the sum nor the average of the meters. It is now the sum of every meter reporting in that minute. Plants receive this with their next agent update.

mirox 2.14.38 – 2.14.48mirox-agents 3.1.43 – 3.1.55
AgentImprovements and fixesProduction & yield

The clear-sky curve is complete again. A device's web interface opens on its own start page again.

  • The clear-sky curve no longer breaks off between yesterday midday and midnight.
  • A device's web interface opens on its own start page again, not on a link that no longer works.
  • A plant's operating state is right again straight after the on-site agent restarts, instead of staying unknown until it next changes.
  • The data logger a combiner box or string is read from is now shown, as it already was for inverters.
  • The manufacturer of a device found by a network scan is now filled in from its hardware address.
  • Expected energy from the irradiation sensor and from satellite data is now also kept as a live running total, next to the live expected power.
mirox 2.14.38 – 2.14.48mirox-agents 3.1.43 – 3.1.55
Web appImprovements and fixesData collection

Agent-started wizard runs can be stopped, unresponsive runs end as failed after 30 minutes, and the agent configuration tab leaves the data-flow page.

  • A wizard run started by the on-site agent can be stopped by anyone who can see it.
  • A run that stops responding no longer sits on waiting and is marked failed after 30 minutes.
  • The plant's data-flow page no longer shows the agent configuration tab to organization admins and moderators.
mirox 2.14.26 – 2.14.37
Web appImprovements and fixesThe app itself

A network scan can now be limited to a subnet inside the plant's networks, and the monthly production chart keeps a slot for every day.

  • The monthly production chart now keeps a bar slot for every day of the selected range, leaving days without data empty.
  • A "Network scan" dialog now limits a scan to a subnet inside the plant's networks, and a device's type is picked from a fixed list.
  • A changed peak power, self-consumption, location or commissioning date now reaches a plant's on-site agent by itself, and the "Core Data" page shows the update.
  • The device search on a plant's "Networking" page now matches name, vendor, type, description, serial number, OS and MAC address as well as IP address.
  • The plant image is now shown in 4:3, and the upload dialog previews exactly how it will be cropped.
  • Adding an inverter or module type by hand no longer fails with an unexpected error.
mirox 2.14.18 – 2.14.25